Technology of laying gypsum tiles along with your hands
Gypsum tiles must be laid correctly, as not just the aesthetic look of decorative facing, but in addition the service life of the
material will be based on the technologies of work. The product is universal, and it may be connected to plaster, concrete, brick
or gypsum board sheets, provided that the top layer of the foundation is even and has no defects.
In the event the flaws of the foundation are significant, it should be completely treated with primer, and then a cement mortar is
made, which matches all of the cracks. Subsequently the surface ought to be primed and dried. Primer therapy is necessary to
improve the bond between the tile and the walls. In this case, its composition should select a special, containing components that
prevent the look of fungus and mould.
In the modern interior of the rooms most frequently used gypsum tiles, imitating natural brick or stone. To execute cosmetic
finishing yourself, it is essential first of all to choose a strategy of tile positioning and prepare a solution. It is important
to focus on the opposite side of the material. When its surface has an embossed surface, then the adhesive ought to be put using
an trowel, also if it is even, then using a top notch one.
The technologies of this job is as follows:
* A thin layer of adhesive mortar is applied to the pre-prepared wall. It’s spread over the foundation so it is likely to place
4-5 tiles. Decorative cladding may be placed both on plasterboard, and on putty.
* Cover the back side of these tiles with glue.
* Plaster elements are pushed against the walls and their location is adjusted. To align the seams, it is suggested to use
spacers.
* masterfasada.ru Finishing is performed in rows, each of which ought to be changed by half a tile. Facing is carried out to the corners of the
room, then immediately get rid of any residual mortar in the joints.
Drying the walls takes no more than a day and demands a continuous humidity and temperature in the room. The final stage in the
laying of gypsum tiles is that their decoration. To get this done, the joints between these elements are filled with a unique
solution, the color of which suits the brick.
Decorative imitation of brickwork on the walls will be carried out in the following ways:
* Cutting on the surface of the seams of masonry with a bolt cutter with your hands;
* placing of tiles under the brick:
* mimicking the structure and color of the side of a single brick;
* Imitating a fragment of brickwork of several bricks.
The perfect method to decorate”beneath the brick” is the one that enables you to create a functional coating together with the
most appearance of its similarity to natural masonry. All 3 strategies to conduct this kind of finishing functions fulfill the
demands, however, the cutting edge of joints with a bolt will be labor-intensive along with the formation of considerable
quantities of dust, so let us consider more typical ways.
The old finish is removed from the walls, and the outside, if needed, is leveled to eliminate the need to paste plaster on a thick
layer of glue.
Combining such cladding with other kinds of interior finishes could be both systematic and done with no clear consistency,
chaotically, together with imitation of signs of aging.
With the support of cosmetic gypsum tiles it’s possible to mimic a lot of textures.
A large number of textures may be imitated with the support of decorative gypsum tiles.
The wall where it’s to be set up must have the following characteristics:
* Hardness and intensity of the surface;
* The absence of uneven areas and sharp sections;
* not any deformations.
Cosmetic tiles at the interior of this kitchen
Walls are made from a variety of substances, so let’s break down the principles of setup.
When working with concrete, there will be no big problems. It is only necessary to take into account the porosity of the material.
Concrete, which has virtually no pronounced pores, should be treated with a fantastic primer.
Mounting gypsum tiles concrete
Before starting work on the setup of gypsum tiles in the walls, then it is worth checking the strength of this surface. When the
plaster does not drop off the walls and at precisely the same time holds well, it is possible to simply paint it using primer.
Mount the tiles onto the painted concrete should not. The surface ought to be scratched, ensuring to misfire, and it ought to be
grouted and coated with a coating of plaster.
Leave a Reply